Board and Batten Siding

What is Board and Batten Siding?

Board and Batten Siding could also be a kind of exterior facade cladding which is placed vertically or horizontally within the type of boards and battens (panels and slats). For the first time, this system is used in Norway and Switzerland for canopy purposes then this system has been utilized in facades, barns and western houses within the us of America (USA). Nowadays this system regained popularity within the us of America (USA) because people are using it during a contemporary way and it’s a rustic view on the surface while wrapping the building construction and make the facades.

While traditional board and batten siding uses wide boards and overlying narrow battens, there are many different techniques and patterns to undertake to to standard narrow over wide technique. For example; reverse board and batten panels, installing wide boards over narrow battens, etc. there’s also overlapping wide boards alternative which is board and board without battens.


There are many reasons to use this system . variety of these :

1. It is resistant,
2. The cost of construction is cheap compared to other external facades,
3. Installing Board and Batten doesn’t require qualified personnel
4. The materials are simple and you’ll find it anywhere.
5. There are many kinds of patterns and hues 
6. Click here to read the blog post about: Board And Batten Siding Advantages and disadvantages 
7. How to Build Board and Batten Siding Exterior Walls?
8. Vinyl Board and Batten Siding

Building Board and Batten Siding Exterior Walls

When boards installed up and down (vertical siding), they're doing not regularly intersect stud framing members like horizontally installed boards do. This problem had been solved by adding horizontal framing pieces between studs called blocking. Installing blocking could also be tons of labor and maybe impractical remodeling work. Blocking also reduces the space within the wall cavity for insulation and should make it hard to run wires and thus the technical system in walls.

Probably the foremost common using is 1×10 boards and 1×2 or 1×3 batten. you’ll also use 1×8 1×12 board and 1×4 battens. To eal out the moisture problem, the boards should be in sound condition and free of open knots, and thus the battens should lap 3/4 inch (1,9cm) onto the boards on all sides .

What Materials Are Used For Build Board and Batten Siding?

List of Board and Batten Siding Materials :

Hammer or nail gun, miter saw or circular saw , Jigsaw, tape , Drill, Level, Caulking gun, Utility knife, T-bevel, Stapler, Boards and battens, Board for the water level , Stainless-steel or galvanized siding nails, Caulk, Primer.

Advice: Cedar are getting to be an honest choice as a staple because it’s soft. Harder wood like pressure-treated pine won’t seal also and it’s more likely to crack.

This system are often installed onto plywood or OSB (Oriented strand board) sheathing. If your sheathing isn’t solid, you’ll need to do attach horizontal furring strips first.

The nails must be compatible with the precise wood species that you simply simply will use because some woods will react with other materials and it’ll cause discoloration at the fastener site. Specially designed tips of siding nail will help to prevent splitting of the siding. Nails will need to be long enough to undergo the siding and into a solid wood substrate a minimum of 1 1/4″(0,63mm). The nails you’re going to use must be hot dipped galvanized steel or stainless steel , otherwise, they’ll cause problems later. Screw Length and Size for Board and Batten Siding Installing is additionally important.

If you’re going to paint or stain your siding, consider finishing all four sides (front, back and both ends). additionally , if you’re going to use solid colors on your siding, consider a base ground , it’ll be beneficial. Some paints and stains perform well without a primer, but even with these products, most will enjoy quite one coat of finish and/or starting with a ground .

Board and Batten Siding Installing Steps

First of all, you'd wish to put water trays on the wall. All around house or your structure, install 1×6 or wider water level , with its bottom edge 2 inches below the sill plate. Snap level chalk lines to help you keep the water-table boards straight and fasten them by driving two or three nails at each stud.

You have to measure the wall to be made will determine the door and window gaps and according to them, your work are getting to be tons easier than the other way.

Put the first board then check and thus the nailing phase will start. The gap is set by the pattern as a pattern for the gap and thus the boards still insert. After the boards are getting to be placed, the battens are getting to be placed between the boards which they're nailed.

Optionally you’ll paint the boards and you’ll finish your sidings. Enjoy your board and batten siding installing 🙂

How to Choose Material for Board and Batten Siding Installing

Board and Batten Siding could also be a kind of coating made up of different materials. Wood, processed wood products, vinyl, fiber cement board are options like . you need to investigate to hunt out out the suitability of these materials. Advantages and disadvantages should be identified.

There are options like redwood, cedar, and cypress. These species are often used. For wood, the likelihood of insects shouldn’t be forgotten and solutions should be introduced to increase the resistance to water and fire. The aesthetic suitability of the wood makes it preferable relying on the climate.

Vinyl could also be a cloth that lasts longer than wood and requires less maintenance.

Fiber cement boards are almost like concrete. they provide long-lasting durability, very low maintenance, doesn’t require. Moisture and fire resistant make it one of the foremost preferred but its weight and artificial appearance and thus the undeniable fact that it produces plenty of dust during construction are the reasons for this material to drop.

Conclusions the material options are very extremely. When taking attention to climate and building criteria, calculating the tactic and cons of it’ll have great benefits.

Board and batten siding application can provide the user from many sources. Online shopping sites, seen because the plus of today’s technology, are the reflection of this. Amazon, e-bay, James Hardie and Chinese original Alibaba, also as sites are often found within the littlest local sites, it’s possible to hunt out plenty of resources. The external coating kind of a separate discipline is that the local company. Also, if simply kind of wood like are getting to be used, it’s possible to provide small businesses kind of a carpenter. The local suppliers are included during this job and see as a special business , you’ll find the material whenever .

Article Resources :
https://boardandbattensiding.net/how-to-install-board-and-batten-siding/
https://www.finehomebuilding.com/2014/05/16/how-to-install-board-and-batten-siding